WIND RMC 445B 240-230 EF

Product code P910040 00002

Operator for shutters with spring holder pulley diam. 101 mm. Max. torque 445 nm and absorbed power 1200 W. Release with steel cable and knob for electric brake.

PLUS
  • Simple and intuitive adjustment of limit switches

  • Adapters for 42 or 48 (RMB) or 76mm (RMC) shafts included in the pack

Assistance

Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.

Report a suspicious product or e-partner
technical design WIND RM
Control unit ELBA/ELBA BU
Power supply 230 V
Power input 1200 W
Shaft diameter 101 mm
Spring holder diameter 240 mm
Maximum torque 445 nm
Rotation speed 8 Rpm
Locking Electric brake
Impact reaction no
Protection rating IP20
Environmental conditions -10 ÷ 50 °C
U-Link no
Imperial measurements

The data shown are for information purposes only.

Control unit ELBA/ELBA BU
Power supply 230 V
Power input 1200 W
Shaft diameter 3.9763801 inch
Spring holder diameter 9.448824 inch
Maximum torque 445 nm
Rotation speed 8 Rpm
Locking Electric brake
Impact reaction no
Protection rating IP20
Environmental conditions 14 ÷ 122 °F
U-Link no
Recommended - Recommended control panel
ELBA
ELBA BU
Compatible - Compatible control panel
ALPHA SD

SHEDIR B CBC 02 L01 Cod. P111515Control unit for wired centralisation. For 2 operators (or 2 groups of operators).
Application: wire centralisation board for 1 or 2 tubular...
Control unit for wired centralisation. For 2 operators (or 2 groups of operators).
Application: wire centralisation board for 1 or 2 tubular motors.
Board power supply: 230V single-phase.
Operator power supply: 230V 600W max. each operator.
Main characteristics: simplified and compact wire centralisation system.
Functions: control of 1 or 2 motors (or motor units) in single or simultaneous mode, general up/down, motor 1 or unit 1 up/down, motor 2 or unit 2 up/down.

ELBA Cod. D113716 00002Control panel, max 230V, for roller shutters or roll-up doors.
Application: control panel for REEL type operator for roller shutters.
Board...
Control panel, max 230V, for roller shutters or roll-up doors.
Application: control panel for REEL type operator for roller shutters.
Board power supply: 230V single-phase.
Operator power supply: 230V monophase.
Main features: Extremely compact size for installation in shutter case, programming with potentiometers and dip switches, built-in receiver.
Main functions: separate open/close, photocells input, possibility of centralised controls, anemometer and twilight sensor management.
Compatibility: CAPRI, CAPRI RIC, CAPRI TCA.

CMS Cod. D831081Sign.Sign.

BOX Cod. N574039Wall safe for unlocking with steel cable and electrical control; cable not included.Wall safe for unlocking with steel cable and electrical control; cable not included.

X EF1 Cod. N999510Electric brake for Wind Rmc and Rmb 230V.Electric brake for Wind Rmc and Rmb 230V.

View all the accessories

This website uses profiling cookies (own and of other websites) for the purpose of sending advertising messages in line with the preferences expressed by the user in the context of web browsing. By continuing to browse or by accessing any element of the website without changing the cookie settings, you implicitly accept to receive cookies on our website. The settings of the cookies can be changed at any time by clicking on Information or using the Privacy link located at the bottom of the page.

An unexpected error occurred: please reload the page or try again later.