REEL EASY B20 230V W45

Product code P910052 00002

Wired operator for roller shutters. Max shutter weight 35 kg. max torque 20 Nm and power input 180 W. Shaft rotation speed 16 Rpm

Main features
  • The KIT version comes complete with all accessories for proper installation as well as operators already arranged in the special telescopic roller, able to adapt perfectly the size of the frame with a single action

  • New range complete with 1 to 5-channel PAD radio controls, features a modern design to suit any home context

  • New Shedir compact wire centralisation board: easily installed even in the boxes of roller shutters thanks to its small size, it can control up to two motors or motor units in single or centralised mode.

Recommendation

Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.

Report a suspicious product or e-partner
technical design
Motor power supply 230 V
Power consumption 180 W
Outer diameter 60 mm
N° limit switch revolutions 28
Type of end switch Mechanical
Locking Mechanical
Frequency of use Residential
Protection rating IP44
Environmental conditions -10 ÷ 40 °C
Interconnectivity no
Release ---
SHEDIR B CBC 02 L01
P111515

Control unit for wired centralisation. For 2 operators (or 2 groups of operators) Application: wire centralisation board for 1 or 2 tubular motors Card power supply: 230 V single-phase Operator power supply: 230V 600W max. each operator Main characteristics: simplified and compact wire centralisation system Functions: control of 1 or 2 motors (or motor units) in single or simultaneous mode, general up/down, motor 1 or unit 1 up/down, motor 2 or unit 2 up/down

Control unit for wired centralisation. For 2 operators (or 2 groups of operators) Application: wire centralisation board for 1 or 2 tubular...

MIME PAD
P121028

4-channel wall-mounted radio control with rolling code

MIME TX
D113831

Two-channel miniaturized 433 Mhz transmitter

SCS 1
P111376

Serial board for connection to zone and opposing leaves for control units with display While stocks last

CREP
P111183

Twilight sensor

ANEM
P111182

Anemometric ​​sensor with encoder for wind

SM504
P130015

Support with bearing for octagonal roller - screw type

SM5014
N999325

Wall support for operators with square snap pin and split pin for direct coupling, suitable for all operators (from 10Nm to 50Nm).

CAL 60/30
P130004

Octagonal cover for RUL 60.

CAL 60/100
P130002

Adjustable telescopic octagonal cover for RUL 60.

RUL 60/3
P130012

Octagonal shutter winding roller Ø60 mm x 3 m.

BLOCCANTI 40
P130001

Anti-break-in block for shutters with slats of height 40 mm.

BLOCCANTI 50
P130013

Anti-break-in block for shutters with slats of height 50 mm.

MIME AC
D113824

433 MHz two-channel indoor receiver 2 independent outputs 230 Vac power supply 30-position memory Operating mode: monostable, bistable, timed, motor control

433 MHz two-channel indoor receiver 2 independent outputs 230 Vac power supply 30-position memory Operating mode: monostable, bistable,...

MITTO B RCB04 R1 CLEAR ICE
D111947

Transmitter with 4 channels. Range 50/100 m. 12 V power supply with 1 23 A battery. Colour clear ice white. Buttons panel can be customised with own design/logo.

Transmitter with 4 channels. Range 50/100 m. 12 V power supply with 1 23 A battery. Colour clear ice white. Buttons panel can be customised...

MITTO B RCB04 R1
D111906

Transmitter with 4 channels. Range 50/100 m. Power supply 12 V with 1 battery type 23 A

MITTO B RCB02 R1
D111904

Transmitter with 2 channels. Range 50/100 m. Power supply 12 V with 1 battery type 23 A

An unexpected error occurred: please reload the page or try again later.