Motors for the automation of up-and-over garage doors for intensive use

BERMA R

Product code P915007 00001
  • DIMENSIONAL DIAGRAM
technical design BERMA
Technologies
  • The new coding system for direct cloning of remote controls.
    Based on microprocessor technology, this system allows the cloning of any MITTO remote control in a MITTO REPLAY remote control.
    In fact, the first remote control "teaches" the second one the correct code which is automatically saved in the receiver the first time it is used.
    Everything occurs at the highest levels of security thanks to the use of the Rolling Code safe transmission system.

Hydraulic operator for overhead garage doors of maximum surface area 9 m² and very intensive use.

PLUS
  • Release system that can also be activated from outside by a steel cable in the SEB version.

  • The by-pass valves allow the exact setting of the torque separately and independently for opening and closing.

  • The hydraulic slowdown guarantees silent, smooth movements on even the biggest doors. Also, the adjustment screw makes it possible to adapt the slowdown intensity to each situation.

Recommended control panel
RIGEL 5
Compatible control panel
ALCOR N
ALPHA SD
Assistance

Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.

Technical Data
Impact reaction Hydraulic clutch
Slowdown Hydraulic
U-Link No
Control unit Rigel 6
Power input 250 w
Locking Hydraulic
Release Knob
Frequency of use Very intensive
Protection rating Ipx5
Environmental conditions -15 ÷ 60 °c
Door surface area 9 m²
Nominal voltage 230 v
Accessories

Recommended accessories.

  • ALCOR AC A Cod. D114092 00002 Dip switch and potentiometer control panel for one or two 230 V/300 W operators for swing gates. Dip switch and potentiometer control panel for one or two 230 V/300 W operators for swing gates.

  • CAS1L Cod. N733074 Straight arm accessories for installation of one Berma operator L = 1500 mm Spain version. Straight arm accessories for installation of one Berma operator L = 1500 mm Spain version.

  • CA2C Cod. N733041 Accessories for the installation of two BERMA series operators on overhead door (curved arms). Accessories for the installation of two BERMA series operators on overhead door (curved arms).

  • CAS2L Cod. N733075 Straight arm accessories for installation of two Berma operators L = 1500 mm Spain version. Straight arm accessories for installation of two Berma operators L = 1500 mm Spain version.

  • CA1C Cod. N733039 Curved arm accessories for installation of one BERMA series operator on overhead door of 4 m max width (curved arms). Curved arm accessories for installation of one BERMA series operator on overhead door of 4 m max width (curved arms).

  • CA2 Cod. N733040 Straight arm accessories for installation of two BERMA series operators on overhead door. Straight arm accessories for installation of two BERMA series operators on overhead door.

  • ALPHA SD Cod. D113680 00002 Universal control panel with potentiometers for one 230V/500W single-phase operator. Universal control panel with potentiometers for one 230V/500W single-phase operator.

  • SEB Cod. N733020 External key release for BERMA, FORB, IGEA LB and IGEA LB BT. External key release for BERMA, FORB, IGEA LB and IGEA LB BT.

  • CA1 Cod. N733038 Straight arm accessories for installation of one BERMA series operator on overhead door of 4 m max width. Straight arm accessories for installation of one BERMA series operator on overhead door of 4 m max width.

  • CAS1 Cod. N733042 Straight arm accessories for installation of one Berma operator L = 1000 mm Spain version. Straight arm accessories for installation of one Berma operator L = 1000 mm Spain version.

  • CAS2 Cod. N733048 Straight arm accessories for installation of two Berma operators L = 1000 mm Spain version. Straight arm accessories for installation of two Berma operators L = 1000 mm Spain version.

View all the accessories

This website uses profiling cookies (own and of other websites) for the purpose of sending advertising messages in line with the preferences expressed by the user in the context of web browsing. By continuing to browse or by accessing any element of the website without changing the cookie settings, you implicitly accept to receive cookies on our website. The settings of the cookies can be changed at any time by clicking on Information or using the Privacy link located at the bottom of the page.

Continue
Information

An unexpected error occurred: please reload the page or try again later.