PEGASO BCJA645W11
Product code P925203 00007Electromechanical operator, deadman, for industrial sectional doors with max surface area 45 m² and use intensive. Power supply 400 V. max speed 24 Rpm. max torque 100 nm. Chain release. IP54.
PLUS
Management system for stop and intermediate limit switches based on absolute encoder technology with settable zero position.
Control unit with deadman feature on-board operator
Ready-to-use cables with quick-fit connectors.
Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.
Report a suspicious product or e-partner
| Nominal voltage | 400 V |
| Power input | 980 W |
| Max surface area | 45 m² |
| Shaft diameter | 25.4 mm |
| Door surface area | 45 m² |
| Travel | 18 |
| Type of limit switch | Absolute encoder |
| Locking | Mechanical |
| Release | Chain release |
| Frequency of use | intensive |
| Protection rating | IP54 |
| Environmental conditions | -10 ÷ 50 °C |
| U-Link | no |
PEGASO CABLE MONO Cod. D121631Pre-wired power supply cable for PEGASO single phase operators. Length 1 m.Pre-wired power supply cable for PEGASO single phase operators. Length 1 m.
PEGASO CABLE TRI Cod. D121632Pre-wired power supply cable for PEGASO three-phase operators. Length 1 m.Pre-wired power supply cable for PEGASO three-phase operators. Length 1 m.
PEGASO UP CONTROL 5 Cod. D121624Cable with pre-wired OPEN - STOP - CLOSE keypad for PEGASO UP operators. For adjusting motor limit switches from floor level. Length 5 m.Cable with pre-wired OPEN - STOP - CLOSE keypad for PEGASO UP operators. For adjusting motor limit switches from floor level. Length 5 m.
PEGASO UP CONTROL 10 Cod. D121625Cable with pre-wired OPEN - STOP - CLOSE keypad for PEGASO UP operators. For adjusting motor limit switches from floor level. Length 10 m.Cable with pre-wired OPEN - STOP - CLOSE keypad for PEGASO UP operators. For adjusting motor limit switches from floor level. Length 10 m.
PEG CCP Cod. N999468Extension for PEGASO C operators release chain. Length 4 m.Extension for PEGASO C operators release chain. Length 4 m.
PIG 12/ULISSE S Cod. N733338Z12 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.Z12 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.
PIG 14/ULISSE S Cod. N733336Z14 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.Z14 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.
PIG 18/ULISSE S Cod. N733339Z18 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.Z18 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.
PIG 30/ULISSE S Cod. N733337Z30 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.Z30 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.
COR 30 Cod. N733148Z30 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.Z30 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.
COR 40 Cod. N733149Z40 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.Z40 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.
SFZ Cod. N733121Additional fixing bracket kit. To be used on chain drive installations.Additional fixing bracket kit. To be used on chain drive installations.
PEGASO ADA Cod. N733449PEGASO ADA adapter for installation on doors with 1"1/4 shaft.PEGASO ADA adapter for installation on doors with 1"1/4 shaft.
