REEL EASY RUA A20 230V R45
Product code P910047 00002Radio operator for roller shutters. Max shutter weight 35 kg. Max torque 20 Nm and power input 180 W. Shaft rotation speed 16 Rpm
Main features
The KIT version comes complete with all accessories for proper installation as well as operators already arranged in the special telescopic roller, able to adapt perfectly the size of the frame with a single action
New range complete with 1 to 5-channel PAD radio controls, features a modern design to suit any home context
New Shedir compact wire centralisation board: easily installed even in the boxes of roller shutters thanks to its small size, it can control up to two motors or motor units in single or centralised mode.
Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.
Report a suspicious product or e-partner
Control unit | Built-In |
Motor power supply | 230 V |
Power consumption | 180 W |
Outer diameter | 60 mm |
N° limit switch revolutions | 28 |
Type of end switch | Electronic |
Locking | Mechanical |
Frequency of use | Residential |
Protection rating | IP44 |
Environmental conditions | -10 ÷ 40 °C |
Interconnectivity | no |
Release | --- |

SHEDIR B CBC 02 L01
Cod. P111515
Control unit for wired centralisation. For 2 operators (or 2 groups of operators) Application: wire centralisation board for 1 or 2 tubular motors Card power supply: 230 V single-phase Operator power supply: 230V 600W max. each operator Main characteristics: simplified and compact wire centralisation system Functions: control of 1 or 2 motors (or motor units) in single or simultaneous mode, general up/down, motor 1 or unit 1 up/down, motor 2 or unit 2 up/down
Control unit for wired centralisation. For 2 operators (or 2 groups of operators) Application: wire centralisation board for 1 or 2 tubular...

MIME PAD
Cod. P121028
4-channel wall-mounted radio control with rolling code

MIME TX
Cod. D113831
Two-channel miniaturized 433 Mhz transmitter

ELBA
Cod. D113716 00002
Control panel, max 230V, for roller shutters or roll-up doors Application: control panel for REEL type operator for roller shutters Card power supply: 230 V single-phase Operator power supply: 230V monophase Main features: Extremely compact size for installation in shutter case, programming with potentiometers and dip switches, built-in receiver Main functions: separate open/close, photocells input, possibility of centralised controls, anemometer and twilight sensor management Compatibility: CAPRI, CAPRI RIC, CAPRI TCA
Control panel, max 230V, for roller shutters or roll-up doors Application: control panel for REEL type operator for roller shutters Card...

SCS 1
Cod. P111376
Serial board for connection to zone and opposing leaves for control units with display While stocks last

CREP
Cod. P111183
Twilight sensor

ANEM
Cod. P111182
Anemometric sensor with encoder for wind

SM504
Cod. P130015
Support with bearing for octagonal roller - screw type

SM505
Cod. P130014
Support for octagonal roller - cementing type

SM5014
Cod. N999325
Wall support for operators with square snap pin and split pin for direct coupling, suitable for all operators (from 10Nm to 50Nm).

CAL 60/30
Cod. P130004
Octagonal cover for RUL 60.

CAL 60/100
Cod. P130002
Adjustable telescopic octagonal cover for RUL 60.

RUL 60/3
Cod. P130012
Octagonal shutter winding roller Ø60 mm x 3 m.

RUL 60/6
Cod. P130008
Octagonal shutter winding roller Ø60 mm x 6 m.

BLOCCANTI 40
Cod. P130001
Anti-break-in block for shutters with slats of height 40 mm.

BLOCCANTI 50
Cod. P130013
Anti-break-in block for shutters with slats of height 50 mm.

Timer
Cod. P130024
Weekly programmer for REEL RADIO or external ER-1 receiver

MIME AC
Cod. D113824
433 MHz two-channel indoor receiver 2 independent outputs 230 Vac power supply 30-position memory Operating mode: monostable, bistable, timed, motor control
433 MHz two-channel indoor receiver 2 independent outputs 230 Vac power supply 30-position memory Operating mode: monostable, bistable,...

MITTO B RCB04 R1 CLEAR ICE
Cod. D111947
Transmitter with 4 channels. Range 50/100 m. 12 V power supply with 1 23 A battery. Colour clear ice white. Buttons panel can be customised with own design/logo.
Transmitter with 4 channels. Range 50/100 m. 12 V power supply with 1 23 A battery. Colour clear ice white. Buttons panel can be customised...

MITTO B RCB04 R1
Cod. D111906
Transmitter with 4 channels. Range 50/100 m. Power supply 12 V with 1 battery type 23 A

MITTO B RCB02 R1
Cod. D111904
Transmitter with 2 channels. Range 50/100 m. Power supply 12 V with 1 battery type 23 A

ELBA BU
Cod. D113717 00002
Control panel, max 230V, for roller shutters or roll-up doors Application: control panel for one roll-up door operator Card power supply: 230 V single-phase Operator power supply: 230V monophase Main features: Extremely compact size for installation in shutter case, programming with potentiometers and dip switches, built-in receiver, control button on case Main functions: separate open/close, photocells input, possibility of centralised controls, anemometer and twilight sensor management Compatibility: CAPRI, CAPRI RIC, CAPRI TCA
Control panel, max 230V, for roller shutters or roll-up doors Application: control panel for one roll-up door operator Card power supply:...