Barrier with 230 V motor power supply for clear opening up to 6 m and opening time 8 s. Impact resistance by means of Sensitive edge. Grey RAL 7015
Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.Report a suspicious product or e-partner
For safe transmission. BFT transmitters use a rolling code system that manages the commands in a completely secure way and prevents any type of external violation. When a transmitter key is pressed the command is sent to the control unit with a different code each time, identifiable only by the receiver and accepted only once. The algorithm generated then prevents the reproduction of the code.
For fast and safe programming. EELINK is a system developed by BFT which, by means of connection to handheld programmers (Unipro, Uniradio and Proxima), makes it possible to transfer data from automatic systems to PCs and vice versa. Thus EEdbase or U-base, the databases of the information stored in the installed systems, are constantly updated. Thanks to this software it possible to associate the necessary personal details with each system: owner's address and details, name of maintenance technician, names of every remote control holder, etc. With EElink, just press a few buttons to easily manage the customer base or preventive maintenance. Even operations that were once complex become easier: for example, reconfiguring the control unit or the radio receiver in case of replacement or the setup of a control panel, starting from a standard or custom configuration.
The new coding system for direct cloning of remote controls Based on microprocessor technology, this system allows the cloning of any MITTO remote control in a MITTO REPLAY remote control. In fact, the first remote control "teaches" the second one the correct code which is automatically saved in the receiver the first time it is used. Everything occurs at the highest levels of security thanks to the use of the Rolling Code safe transmission system.
|Control unit||ALPHA BOM|
|Motor power supply||230 V|
|Power consumption||300 W|
|Type of limit switch||Electronic|
|Impact reaction||Sensitive edge|
|Frequency of use||Semi intensive|
|Environmental conditions||-20 ÷ 50 °C|
Anchor base for MOOVI and GIOTTO series barriers
Complete 3 metre rectangular boom for GIOTTO and MOOVI
Complete 5 metre rectangular boom for GIOTTO and MOOVI
Pack of accessories for installation of 3/5 m rectangular boom for MOOVI/GIOTTO
Complete 3 metre round boom for MOOVI/GIOTTO
Complete 5 metre round boom for MOOVI/GIOTTO
Complete 6 metre round boom for MOOVI/GIOTTO
Pack of accessories for installation of 3/6 m round boom for MOOVI/GIOTTO
Rest fork for booms. For bolting to ground.
Pack of 12 additional reflective labels (1 pack already included with each boom)
ART 90 Q
90 ° articulated joint for Moovi and Giotto booms. Max 4m clear passage.
Aluminium skirt for road barrier booms. Price per linear metre (Calculate length of useful passage minus 40cm)
Cod. P120001 00001
Lights on boom 3 - 4.5 m
Cod. P120001 00002
Lights for booms over 4.5 m
Cod. P120028 00001
Top and bottom rubber cover profile for booms of 3 m max.
Cod. P120028 00003
Top and bottom rubber cover profile for booms of 5 m max.
Cod. P120028 00004
Top and bottom rubber cover profile for booms of 6 m max.
Additional anchor plates for cementing FAF2 forks to ground.
Mobile rest leg for BGV barrier boom (not usable on BGV 30)
GA AQ AT
Movable support leg for AQ or AT booms (on MOOVI, MICHELANGELO and GIOTTO barriers) -
GAMA AQ AT
Dampened movable support leg for AQ or AT booms (on MOOVI, MICHELANGELO and GIOTTO barriers) -
Rubber safety edge (H 30 mm), price per m
Cod. P111401 00001
Infrared device for BIR C or BAR C safety edges (conforms to EN 12978 Standard)
Serial board for connection to zone and opposing leaves for control units with display While stocks last
Cod. D110926 00001
Magnetic loop 2 x 1 m