PEGASO BCJA625L01

Product code P925203 00004
  • DIMENSIONAL DIAGRAM
technical design PEGASO B CJA AUTO

Automatic electromechanical operator for industrial sectional doors with max surface area 25 m² and use Semi intensive. Power supply 230 V. max speed 24 Rpm. max torque 70 nm. Chain release. IP54.

PLUS
  • Management system for stop and intermediate limit switches based on absolute encoder technology with settable zero position.

  • Control unit with deadman feature on-board operator

  • Ready-to-use cables with quick-fit connectors.

Recommended control panel
LEO B CBB L01
Assistance

Attention: To benefit from the official warranty on Bft products purchased online, you must check that the retailer is approved by Bft.

Technical documentation
Technical Data
Type of limit switch Absolute encoder
U-Link No
Control unit Leo b cbb l01
Power input 750 w
Locking Mechanical
Release Chain release
Frequency of use Semi intensive
Protection rating Ip54
Environmental conditions -10 ÷ 50 °c
Door surface area 25 m²
Nominal voltage 230 v
Shaft diameter 25.4 mm
Max surface area 25 m²
Travel 18
Accessories

Recommended accessories.

  • PEGASO CABLE AUTO 5N Cod. D121679 Pre-wired connection cable between PEG INT and external control unit electric power supply. Length 5 m. Pre-wired connection cable between PEG INT and external control unit electric power supply. Length 5 m.

  • PEG CCP Cod. N999468 Extension for PEGASO C operators release chain. Length 4 m. Extension for PEGASO C operators release chain. Length 4 m.

  • PIG 14/ULISSE S Cod. N733336 Z14 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts. Z14 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.

  • COR 40 Cod. N733149 Z40 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts. Z40 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.

  • FALCON Cod. P111407 Industrial presence sensor installable up to 7 m. Industrial presence sensor installable up to 7 m.

  • PEGASO CABLE ENC 10 Cod. D121675 Pre-wired connection cable between operator and external control unit for the management of encoder. Lenght 10 m. Pre-wired connection cable between operator and external control unit for the management of encoder. Lenght 10 m.

  • PEGASO ADA Cod. N733449 PEGASO ADA adapter for installation on doors with 1"1/4 shaft. PEGASO ADA adapter for installation on doors with 1"1/4 shaft.

  • PIG 12/ULISSE S Cod. N733338 Z12 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts. Z12 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.

  • COR 30 Cod. N733148 Z30 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts. Z30 gear kit complete with accessories for industrial sectional doors, for 1 " (25.4 mm) shafts.

  • PEGASO CABLE ENC 5 Cod. D121674 Pre-wired connection cable between operator and external control unit for the management of encoder. Lenght 5 m. Pre-wired connection cable between operator and external control unit for the management of encoder. Lenght 5 m.

  • PEGASO CABLE TRI Cod. D121632 Pre-wired power supply cable for PEGASO three-phase operators. Length 1 m. Pre-wired power supply cable for PEGASO three-phase operators. Length 1 m.

  • PIG 30/ULISSE S Cod. N733337 Z30 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts. Z30 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.

  • PEGASO CABLE AUTO 10N Cod. D121680 Pre-wired connection cable between PEG INT and external control unit electric power supply. Length 10 m. Pre-wired connection cable between PEG INT and external control unit electric power supply. Length 10 m.

  • SFZ Cod. N733121 Additional fixing bracket kit. To be used on chain drive installations. Additional fixing bracket kit. To be used on chain drive installations.

  • PEGASO CABLE MONO Cod. D121631 Pre-wired power supply cable for PEGASO single phase operators. Length 1 m. Pre-wired power supply cable for PEGASO single phase operators. Length 1 m.

  • PIG 18/ULISSE S Cod. N733339 Z18 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts. Z18 pinion gear for industrial sectional doors, for 1 " (25.4 mm) shafts.

View all the accessories

This website uses profiling cookies (own and of other websites) for the purpose of sending advertising messages in line with the preferences expressed by the user in the context of web browsing. By continuing to browse or by accessing any element of the website without changing the cookie settings, you implicitly accept to receive cookies on our website. The settings of the cookies can be changed at any time by clicking on Information or using the Privacy link located at the bottom of the page.

Continue
Information

An unexpected error occurred: please reload the page or try again later.